Kugelgewindetriebe sind die am häufigsten verwendeten Übertragungskomponenten in Werkzeugmaschinen und Präzisionsmaschinen. Seine Hauptfunktion besteht darin, eine Drehbewegung in eine lineare Bewegung umzuwandeln oder ein Drehmoment in eine sich wiederholende Axialkraft umzuwandeln. Gleichzeitig zeichnet es sich durch hohe Präzision, Reversibilität und hohe Effizienz aus.
Exzentrizität: Bezieht sich auf die Mittenabweichung zwischen der festen Seite und der tragenden Seite.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60 m/min und Zwangsölnebelschmierung kann als 60 angesehen werden-100m/Min. Es wird empfohlen, eine Hohlschraube zu bestellen und Zwangskühlung und Schmierung einzusetzen. Halten Sie die Arbeitsumgebung sauber und lassen Sie keinen Staub und andere Verunreinigungen in die Laufbahn oder Mutter gelangen. Wenn die Situation nicht gut ist, sollten Sie die Schrauben mit einer Schutzabdeckung versehen.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①Hohe Übertragungseffizienz. Die Übertragungseffizienz der Kugelumlaufspindel beträgt im Allgemeinen 20,92-10 Prozent, und der Übertragungswirkungsgrad eines gewöhnlichen Gleitschraubengetriebes beträgt 20,20-0.40.
②Hohe Übertragungsgenauigkeit, stabile Bewegung und kein Kriechphänomen. Der Kugelgewindetrieb ist im Grunde Rollreibung mit geringem Reibungswiderstand, und der Reibungswiderstand hat fast nichts mit der Bewegungsgeschwindigkeit zu tun.
③Fahren im Rückwärtsgang ohne Leerlauf. Nachdem der Kugelgewindetrieb und die Mutter vor-festgezogen sind, kann das axiale Spiel beseitigt werden. Auf diese Weise gibt es keine tote Zone in der entgegengesetzten Richtung und die Genauigkeit und Steifigkeit des Axialgetriebes werden verbessert.
④Es ist reversibel. Da der Reibungsverlust des Kugelgewindetriebs gering ist, kann er von einer Drehbewegung in eine lineare Bewegung umgewandelt werden, und er kann auch von einer linearen Bewegung in eine Drehbewegung umgewandelt werden. Sowohl die Leitspindel als auch die Mutter können als Antrieb oder Mitnehmer verwendet werden.
⑤Lange Lebensdauer. Aufgrund des geringen Reibungsverlustes der Rollreibung ist die Lebensdauer lang.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
Kontaktieren Sie mich jetzt
E-mail: sales@gyballscrew.com Tel(Whatsapp): plus 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
